Ford Powerstroke Diesel Forum banner
mod
1-20 of 28 Results
  1. General 6.7 Discussion (2017-2019)
    Hey all. Was looking into an aftermarket grill for my rig and was wanting any input I could get on the Rough country grill. With or without the light bars. Just wondering about the quality and the durability of them if anyone has installed one. TIA
  2. General 6.7 Discussion (2017-2019)
    New to all this mod stuff but I am going to be installing an EGR delete on my rig and was wondering if I were to drain the coolant as prescribed and kept it clean if I could re use it to refill when egr delete is finished. Also after egr delete is complete is that all I have to do as far as the...
  3. E-Series Van Discussion
    Hi folks, I talked to Dennis @ strictly diesel about doing the hutch mod to my 2002 e350 7.3. He said "there is a pan surrounding the pickup that prevents the extended return from fitting. We also don’t list this kit as fitting the van because the van fuel tank has a liner that is notorious...
  4. 99-03 7.3L General Discussion
    Hey, new guy/lurker here. I've poked around a fair bit across this site and others regarding this issue as it caught me off guard when I completed my Turbo Rebuild/Upgrade/EBPV delete at work yesterday. I haven't seen this method mentioned. Granted I'm not going to dig super deep to see if I'm...
  5. 6.4L Performance Parts Discussion
    I can finally get my tune becuase My Uncle Sam is returning some of the money he borrows from me every week. I want to get a vote between the two listed for h&s and Spartan. My truck is only drove once every other or or once a month so it sits a lot. I have a snow plow on it and tow derby cars...
  6. 6.4L Performance Parts Discussion
    So I got a truck with a dpf delete on it. I can't find a tuner. I know it has a tune but i don't know what it has. If I do an egr delete, will it throw a code or not since it already has the dpf delete? It would be a whole lot easier to do it now since the head is off. Only use motorcraft glow...
  7. 6.0 Motor problems
    Hey guys I'm back. And I know how we love our videos. Do you think this is normal smoke (oil vapors) from my CCV or could this be Exhaust Blow By??? http://youtu.be/k9HD0xNvJvM It smokes like this hot or cold, fresh start or ran for hours, and does not seem to increase when I step on the...
  8. Powerstroke.org Builds & Projects
    Having seen some interest on this topic from a few members already, I've decided to throw a quick write-up together on this project. This project is about adding solar power to your truck in order to keep your batteries at maximum capacity which will ultimately ensure a longer and healthier...
  9. 6.0 Motor problems
    I just wired up the high idle mod for my late '03. Setup is clean and looks good. Recently though, I've had a strange issue happen when the switch is flicked on. The rpms slowly climb to 1200 but "surges" ( not sure if correct term). The rpms quickly jolt down to 1000-1100 briefly then bounce...
  10. 6.0L Electronics Discussion
    So, I recently had to replace my FICM, and think that it may have been due to low battery voltage. I have Torque, but sometimes it a pain to start the phone, then the app, then wait for Torque to load just to see the volts when starting. So, I found this little digital voltmeter on Amazon, and...
  11. 99-03 7.3L General Discussion
    I'm going to drop my tank and do the hutch mod and harpoon mod while I'm at it. I've seen 2 versions of the hutch mod. One removes everything but keeps the black plastic foot pre-filter on the bottom and the other removes everything and just uses a piece of 90° copper or stainless steel tubing...
  12. 6.4L Performance Parts Discussion
    Looking at some 100% over injector nozzles, wondering if the stock HPFP can handle it. i know the stock HPFP after a 300hp tune is barely able to keep up. so dont know if id need other supporting mods, or just a dual fuelers/ uprgaded pump
  13. 99-03 7.3 Motor Problems
    For those of you who have been helping me with advice or following my thread orig posted at: http://www.powerstroke.org/forum/99-03-7-3-motor-problems/508858-knock.html Any way I went ahead & done the Hutch Mod using: 1 - 3/8" tube compression union 1 - 5/16" tube compression union 3ft - 5/16"...
  14. 6.4L Performance Parts Discussion
    Wired green/yellow to brown and it comes on when I engage the emergency break. Doesnt matter what position aux 4 switch is in. Any ideas on what that could be?
  15. 94-98 7.3L Performance Parts
    So I did the fpr mod with a BB and I'm not sure i like it. I can't tell anything other then a little more smoke and the fact that it acts weird. It seems like it starts worse then it did before. My OSI went from 52-71. Should i just take it out and say forget about it and just wait for my e fuel?
  16. 94-98 7.3L Performance Parts
    Im considering doing the whole 6.0 fan on the 7.3 clutch. Is it a drop in install or would I have to get a new shroud or do any other work other then swap the blades?
  17. 94-98 7.3L Performance Parts
    i just installed rosewood stage 1s yesterday amd i want to know if upgrading to a t500 is really worth iy. what would i belooking at difference wise?
  18. 94-98 7.3L Performance Parts
    Will a napa 6637 filter fit on k&n intake tubes? i have a k&n and I know they are bad want rid of it.
  19. 6.4 Powerstroke Interior Discussion
    Is this possible? That is to say, is it a plug-and-play swap to add digital climate controls to a 2008 F250 XL? Programming the GEM module and/or ECU is no problem; I have a Ford Rotunda VCM.
  20. 94-98 7.3L Performance Parts
    I'm doing injectors and noticed my ccv pipe looks like it was cut. I bought the truck used, and im not sure what the purpose of this is for, buy its definatly not factory. The pipe probably has two inches with a bend going up and is flat, with cut marks. It practically buts up against the intake...
1-20 of 28 Results
Top