Ford Powerstroke Diesel Forum banner

install

  1. 6.7 Exterior Discussion (2011-2016)
    Hey guys, looking to install cab lights on my 2015 6.7 with a sunroof. from what i have read it's fairly simple and because of the sunroof it actually helps you get in there easier. is this true? is there anything in particular i should be aware of with seals and such on the sunroof if im...
  2. 6.7 Electronics Discussion (2011-2016)
    I purchased a used headache rack (not sure of the brand) and it has four wires (green, yellow, brown, and white) hanging out of the rack. The rack has four oval led red lights at the top of the rack and there is a trapezoidal opening cut so that the factory CHMSL (center-high mount stop lamp)...
  3. General 6.0L Discussion
    Yep, finally did it! I've been trying to find some time and yesterday was it. Got it installed, so what did I think? Well designed, easy install, and the small hose clamps are way too dang big. Disappointed by that (They did leak, even fully tightened) - so tomorrow morning I'm running to...
  4. 94-98 7.3L Performance Parts
    Hello, I recently just purchased a 5 inch full aluminum pipe with a 3'' downpipe. I have been poking around here and have not been able to find to much about installing a 5'' pipe. Are there any difficulties i will run into? Will i be able to keep my spare tire? I know the downpipe has its share...
  5. 99-03 7.3 Transmission Problems
    i bent my clutch fork friday night so i figured id go ahead and replace the factory clutch since im at 175,000 miles. i ordered my upgraded organic valair clutch kit and went to ford and got the upgraded fork and a fork mounting stud. is there any tips or suggestions on removal and installation...
  6. 6.7 Performance Parts Discussion (2011-2016)
    Morning Folks. My wife is finally letting me put in my 5'' exhaust, H&S tuner, egr delete and air intake. Problem is I'm much more attuned to woodworking than working on vehicles. I've searched the 6.7 forums and read a bunch of your guys helpful tips but I've just some got newbie questions...
  7. General 6.0L Discussion
    ok i have four glow shift gauges the fuel pressure gauge was working for about 3 1/2 days then just pegged out at 100 psi. i checked my ground and have a complete circuit. when i ohm the wire going back to the gauge with it on the sending unit i have some high ohms when you lift it from the...
  8. 6.0L Performance Parts Discussion
    I have everything to install a fuell pressure gauge and I'm familiar with everything except installing the braided extension line into the fuel port. I'm not sure what to disassemble and how hard things are to get put back together. Can anyone walk me through this? It's asking a lot I know...
  9. 6.0L Problems Forum
    How do you replace a serpentine belt on an '05 F250 6.0 from beginning to end, to include all parts that need to be removed to support easily accessing the tensioner pulley?
  10. 6.4 Electronics Discussion
    After installing the cab lights, and before Dad left for home he asked me to install his Streamlight charger base and lamp in his truck. After looking around, I found a place that was out of the way, easy to get to and secure. I made a quick video explaining the install and just like the cab...
  11. 6.4L Performance Parts Discussion
    I live in Atlanta but have been working out of town for a long time. My Mini Maxx was delivered to Atlanta and I can't wait to install it this weekend. Will it hurt the engine or learning process if I make the 5 hr trip the same day or next day after install?
  12. General 6.0L Discussion
    I disconnected my icp valve to see if it was the reason for no start when warm (it wasn't) Here is a hint on how to reinstall this bugger from the top. DEgas, FICM, FICM bracket and ground bolt removed. I had to slice the protective housing from around the wire so it would move out of the...
  13. 99-03 7.3L Performance Parts
    im about to get the GQSSB turbo kit Swamps 250cc / 100% injectors and ARP head studs and 810 valve springs i think thats right? whats the easiest way to install? i was thinking lift the body... and do you think i should get bigger injectors? and for all this money is this the best way...
  14. 6.0L Powerstroke Interior Discussion
    So i just got my truck back and I started to install my new 08 console that i picked up. Well I got the brackets in place perfectly fine but when I went to bolt the console to the brackets I couldnt get the guide pins or holes to match up. I tried twisting and pulling around on the console with...
  15. 6.4L Performance Parts Discussion
    i live in st louis/st charles and i am looking for a diesel shop to do an install on a turbo back exhaust and a mini maxx tuner on my 2008 6.4. does anybody know any good places around here?
Top