Pulled the cab, bulletproofed my 2005 6.0
Driving around and trans overheating! Have an sct x4. Showing me 250 F. With dash gauge going up as-well.
Here’s what I’ve done-
Unplugged test hose on trans radiator verified pump is working.
drained trans fluid, blew out lines with shop air no...
Alright so I took my truck to the shop and got head studs, new gaskets, FASS Fuel pump, HAYDEN mechanical fan clutch, and KC Stage 2 turbo installed.
I picked up up and drove it to work that evening. A couple hours later I started it up and it died on me within about 10 seconds. Shop came and...
It starts and if I let it idle, within 30 seconds the rpm starts climbing until the wastegate on the turbo activates. causes an idle around 1500. If I tap the brake just barely, then the idle drops back down to 900. Any idea what could be causing it?
DTCS using forscan:
2004 F-350 Bulletproofed 6.0
I just installed the Sinister Diesel Blue Spring Kit. Install went smoothly but the air filter light came up on the dash immediately afterwards. I ran the codes and I ended up having 4 codes (plus the EGR code).
P0113 Intake Air Temp Sensor 1 Circuit High
So before I decided to replace my transmission I was getting codes P0781 and P0782 as well as some slippage under moderate acceleration in 3rd gear. OD light would flash. This only happened when my truck was de-tuned (go figure, less power more problems).
I bought a beefed-up reman and...
OK, I ran across the document here while doing a search on the 2018 DPF system, as a salesman mentioned to me that Ford had one away with DPF a few years ago. Didn't seem to make sense, I should have seen that mentioned here before, but was checking the interwebs anyway. The document in this...
I have seen this thread multiple times but no solutions found. My '06 6.0 is throwing the following ABS codes:
My new hubs have less than 2k miles on them and haven't had any problems until now with the ABS light coming on. It appears that replacing the sensors does...
I just recently replaced my 03 F-250 6.0L, last 6.0 I will ever buy fyi, with a 08 6.4L with 120k miles. I purchased it from a dealer about 80 miles away. They offer a certified vehicle with a 30 day bumper to bumper warranty. The truck runs great got 20 MPG on the lie o meter on the trip home...
My dad's 6.4 received the "Stop Safely Now" message yesterday right after a regen cycle. Pulled over and it died. Contacted a nearby stealership, they had a mechanic about to knock off, he brought 8 different sensors with him to meet up with my dad. They changed out every dpf, egt, etc. sensor...
I plugged my sct tuner in, ran a quicktest, and it threw code p2290 Injector Control Pressure Too Low! What is this problem, i noticed a little jumping when its cold, like some injector stiction, but when it warms up, it runs fine.
I've a 2002 F350 7.3. A few weeks back the engine light started coming on but so far it also goes out. While driving it will just come on with no other indications of a problem but then go out after a little bit of time. I have a Pocket code scanner hooked up to it because it was...
Hello all guru's:
Truck just dies , runs great , tach just quits and dies, only after it gets hot.
will start and run fine for a while after cooling for several hours.
Throws the following codes:
p0603 - int. cntrl mod KAM error
p1670 - ef feedback signal not detected
p0340 - camshaft pos...
HELP!!!! I WILL PAYPAL $50 TO THE PERSON THAT SOLVES/DIAGNOSES MY PROBLEM
I have a 2001 Ford Excursion 4WD Limited
The truck 44,000 Original Miles on it
In an effort to improve Fuel mileage as well as to have functioning gauges, I installed an Edge Juice With additude INSIGHT CS
Back in March when towing a trailer (approx weight: 8K) I was using Tow/Haul and it started flashing within about 5 minutes after engaging. I had the codes checked and the following came up:
P0700 & P0751
I continued to drive the truck not noticing any shifting issues. I have not pulled the...
got my tuner and s&b and straight pipe today and within 2 hours \the engine light came on and my dash daq said
"P0401 EGR flow insufficient detected"
"P1000, OBD systems readiness test not complete"
what did i do? whats that mean? what should i do??
thanks for the help
Ran pretty much all the test I could on it, came up with the following codes: (Same before and after clearing them and running the truck, codes came back after a drive.)
Now the CEL does NOT come on.... except the hard accell (P0238) and then it goes right back off, and the truck runs like a...
Hi - I have a 94.5 powerstroke. It has the OBD2 plug under the glove box area. I wasn't able to pull any code data from the obd2 port, so I did a bunch of reading / searching on this forum and read about people swapping in 96+ computers to enable pulling complete code data via OBD2.