Ford Powerstroke Diesel Forum banner
clutch
1-20 of 31 Results
  1. 94-98 7.3L Problem Forum
    This isn’t a normal situation. I put new u joints on my front driveshaft, then installed it with the slip yoke on the transfer case side which is opposite of what it was before. The slip yoke boot clamps ended up catching some wires and ripped all of my 4x4 wires and other stuff. Only concerned...
  2. 99-03 7.3L Powerstroke Problems
    Last night I installed one of those heim joints onto my clutch master cylinder push rod hoping it will solve the synchronization issues. Now when I push the clutch to the floor, the heim joint body hits the little safety switch mounted onto the rod. Has anyone experienced this before? Is there...
  3. 6.0L Electronics Discussion
    Hello, I posted this in the General Discussion forum and got no replies so I thought I'd ask here, too. I am working on installing a Viper 4806V remote start in my manual 2003 F250 Super Duty 6.0L. I am aware of the risks and, to be as safe as possible, I intend to install a physical switch to...
  4. 94-98 7.3 Trannie Problems
    How do you know when the clutch is wearing out? How do you know when the synchronizers in the transmission are going out? I have occasional trouble with grinding gears while shifting. Clutch can be thrown all the way to the floor so its not that. It happens most often when shifting up or down...
  5. 911 Urgent Situations
    HOW does one go about this - Working on a 2001 F350 and can not get the clutch push rod detached from the master cylinder. NVM: got a phone call with the answer - job complete.
  6. Performance & Drivetrain Parts
    New, Still in box. Never installed. Sold truck. Complete kit. Luk part #07-155. Also includes new clutch release arm Ford part #YC3Z-7515-BB $250 I travel between San Jose and Sacramento, CA area frequently.
  7. 94-98 7.3L Problem Forum
    Can someone please tell me if this is a dual mass flywheel or single. I really need to know ordering a clutch soon.
  8. 6.4L Performance Parts Discussion
    Hi im curious if anyone would know if a zf6 from a 04 6.0 would work in a manual swap in my 2008 with a 6.4. The guy has the trans and all the clutch parts included. Is it worth it? Please help thanks
  9. Tranny 911
    I have a 97 f-250 PSD 5 spd I was wonder if my problem is the throw out bearing or pressure plate or maybe something else??? Ok here's my problem, when I shift from 3 rd into 2nd and when I push the clutch in in 2nd gear to come to a stop I can hear a chatter or rattling noise. Any ideas on what...
  10. 94-98 7.3L General Powerstroke Discussion
    Hello Everybody! I recently purchased a 1996 F350 CCLB with a 7.3 and a 5 speed manual. It has 234,000 miles and was pretty much stock when purchased. I decided to purchase this truck because: A. I really like the OBS crew cab for family trips. B. I like the 5 speed. C...
  11. 99-03 7.3L Performance Parts
    Hey yall, Ive been looking at dual disk clutches for my pick up. just wondering if anyone has had any luck or information on Luk Dual Disk Clutches, seems like a pretty good deal but cant find any reviews on them at all, here is a link to the particular clutch I am looking at. Ford Diesel Twin...
  12. 94-98 7.3L Problem Forum
    My clutch went out so a knowledgeable buddy of mine helped me replace it. The flywheel was tore up too, so replaced the whole clutch set and flywheel. It was a dual mass, the new one is not. Everything seemed to run great the first night. The next morning, I had the "Wait to Start" light come...
  13. General 6.0L Discussion
    Hey All Long time reader, first time posting. I have a 2005 6.0psd and have been having a rattle coming from behind the radiator, upon inspection i fount that the wire coming off of the fan clutch has been cut by the fan. It appears to be a pretty clean cut however i havent found where the...
  14. 6.0L Problems Forum
    My truck was making a chirping noise and it sounded like a belt slipping but it was very faint (I could barely hear it over the engine). I ran the codes on my scanner and the only one that came up was P0528: fan speed sensor no signal. I had my fan clutch replaced about a month ago due to it...
  15. 6.0 Motor problems
    04 6.0, My fan constantly runs and sounds like a windmill running down the road and killing my fuel mileage and power. I have just replaced the bad egr cooler with a delete kit, oil cooler, water pump and fan clutch. THe only thing i havent replaced is the thermostat. After fixing all the stuff...
  16. 99-03 7.3 Transmission Problems
    i bent my clutch fork friday night so i figured id go ahead and replace the factory clutch since im at 175,000 miles. i ordered my upgraded organic valair clutch kit and went to ford and got the upgraded fork and a fork mounting stud. is there any tips or suggestions on removal and installation...
  17. 99-03 7.3 Transmission Problems
    Well the clutch doesn't slip at all but when shifting into certain gears usually 2nd and reverse it will go about half way into gear then as im slowly letting out it will fall into gear the rest of the way. Also the clutch squeaks everytime I push it. Also with the squeak, when pushing in it...
  18. 94-98 7.3L Performance Parts
    Im considering doing the whole 6.0 fan on the 7.3 clutch. Is it a drop in install or would I have to get a new shroud or do any other work other then swap the blades?
  19. 99-03 7.3L General Discussion
    I just got a 2000 6-speed Dually and I noticed the clutch let's out like 1/2" off the floor. The previous owner said he installed a new clutch so I figured it just needed to bled. Upon further inspection I noticed that the aluminum bracket at the top of the clutch pedal is wore so bad that...
  20. 7.3L IDI (Non-Powerstroke) Diesels
    Ok. i have an 89 F350. i changed the master cylinder and the slave cylinder, and now i have about 1/2 the pedal. but no matter how much i pump it up or let it bleed i can't seem to get any more. any advice? i'm stumped at this point.
1-20 of 31 Results
Top