Ford Powerstroke Diesel Forum banner

6.0 and 6.4 auto transmission differences

59K views 31 replies 16 participants last post by  Lubbockguy1979 
#1 ·
According to the 6.4 and 6.0 bibles, the 6.4s use an 8-bolt flywheel/torque convertor set-up and the 6.0s use a 6-bolt flywheel/torque converter set-up. Also, it seems that the 6.0s TCM is integrated into the underhood ECM, while the 6.4s use a seperate TCM mounted to the frame. Other than these differences, are the transmissions interchangeable? In other words, if the transmission in my 2006 went south could I use the transmission (minus the torque converter) from a 6.4? Just curious.

Ryan
 
#2 ·
You either need to get a 8lug fly wheel and tc or a 6lug fly wheel and tc. You cannot missmatch the fly wheels and tc. Dependant on the year of the trannys in question will determine the differences. The tranny should work fine and bolt, and plug in though. The 6.4 has a different stall convertor so if one is better for you use that setup.
 
#11 ·
I know this is a 6yr old quote, but where the f**k did this info come from!?!?

These are internally balanced motors. The flywheel/flex plates are balanced to themselves. They have no bearing on the internal balance of the motor. It is perfectly fine to swap flywheels or plates.
 
#4 ·
I was just curious if Ford made any changes to the transmission itself when they went from the 6.0 to the 6.4. Since posting this topic, I have found out that the Torqshift used with the 6.4s features upgraded internals to handle the extra power that the engine puts out.

Thanks
 
#5 ·
a little bit old topic, but, so if a 6.0 tranny went south you could swap in a 6.4 and it could handle more power, seems pretty neat. THey also changed the pan and filter.
 
#7 ·
Sorry to jump in Fellas ! But a Google search led me to this post and it is Great News if it's True ! I blew my 2010 trans this week ! A good friend just swapped a Cummins setup into his 05 F350 ...he has his factory trans in great shape with less then 70k miles on it . It's mine if I need it for Free! But it's an 05 and mine is 2010 ! Seeing some I'm saving A lot on the free trans I don't mind buying Few necessary parts for it ...I already figured I'd swap a fresh front pump and converter into it . My truck is already complete so I should have the correct flywheel for the converter ."is that it ??? Can I use my flywheel and correct converter for my truck on a 2005 5R110?? That would be Such a Lifesaver !! Thanks for any help !
 
#8 ·
Thread revival!
Yes it's a direct swap, I wouldn't bother changing the front pump, I would get a new 6.4 converter as yours is likely contaminated from your transaction failure, the 6.4 converter will go right in the 6.0 trans.
Also your 6.4 pan and filter are better so I would put the pan and (new) filter on the 6.0 trans.
 
#9 ·
Portcity you seem to be everywhere and have so much useful information. Although this thread doesnt pertain to me I do appreciate you sharing your knowledge with the rest of us! Could you possibly chime in on my thread about tires on our duallys if you have an answer?
 
#12 ·
I can try, where's the thread at?
 
#10 ·
Wait doesnt the above post say that the fly wheels are different? So if my trans goes south, i can get another 03 tq converter and an 08-10 trans from a yard and itll work?
 
#13 ·
The flex plate (flywheel) is only different because the 6.0 converter has 6 studs and the 6.4 has 8 studs to mount it to the flex plate. Yes a 6.0 converter will work fine in a 6.4 trans.
 
#15 ·
What are the guys doing when they swap to billet flex plates then? Rebalancing the whole bottom end? Sounds silly.
 
#23 ·
Jesus......


Take a step back and use some common sense....


The billet flex plate.....hold on to your hat.....IS BALANCED TO ITS SELF!!! Just like the steel factory ones are balanced units.....


If the motor is INTERNALLY balanced, then bolting a BALANCED flywheel/flex plate on to it has 0 effect on the motors balance. No bottom end rebalancing needed.

Further more the international motors used in ford trucks haven't been externally balanced even dating back to the 6.9/7.3IDI motors. Ford in general stopped externally balancing their motors (like GM and MOPAR) back in the 70's because it was too easy to thro off the balance and cause engine damage. A little research before just posting would have avoided this whole conversation....
 
#16 ·
#18 ·
There are only 17 replies.....read the thread.
 
#25 ·
Post #8 clearly states it's a direct swap and mentions the converter options.
But to be more specific you can use the 6.4 trans with your 6.0 converter IF your converter isn't contaminated, and it dosnt matter if it's 2wd or 4wd....all of those parts will swap as well.
 
#30 ·
just to confirm. My 6.4 tranny just **** the bed. I have a good trans for a 6l.

Will my 6.4 converter fit Into the old 6l tranny?

I understand 6l converter into 6.4 trans but what about the other way?
The tranny will work with either convertor assuming you use the proper flywheel. Either fly wheel will fit the 6.0 or 6.4. so... Match the flywheel to the convertor. The motor and transmission will work with either combo

Sent from my SM-G975U using Tapatalk
 
#31 ·
The 6.4 converter will fit just fine but if the transmission it came off of **** the bed, it would probably be a good idea to either change the flex plate and use the 6.0 converter or get a new 6.4 converter.

If the trans passed metal, it's in the converter and will soon be in the trans you put the converter on.
 
#32 ·
The 6.4 converter will fit just fine but if the transmission it came off of **** the bed, it would probably be a good idea to either change the flex plate and use the 6.0 converter or get a new 6.4 converter.

If the trans passed metal, it's in the converter and will soon be in the trans you put the converter on.
Yep. Flush or replace the cooler, replace the toilet paper if you have a 6.0

Sent from my SM-G975U using Tapatalk
 
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top