Flushing and Cleaning the 6.0 - Ford Powerstroke Diesel Forum
 6Likes
  • 4 Post By PGreenSVT
  • 2 Post By TxFireman1972
 
LinkBack Thread Tools Display Modes
post #1 of 2 Old 05-11-2011, 07:38 AM Thread Starter
RIP Mitch ! We miss you

 
PGreenSVT's Avatar
 
Join Date: Mar 2008
Location: Abingdon, Md.
Posts: 11,966
Thanks: 4
Thanked 55 Times in 19 Posts
Mentioned: 0 Post(s)
Quoted: 1 Post(s)
Feedback Score: 3 reviews
Shawn, it hasn't ever been made a sticky but if you would like to add it to the 6.0 tech section it would keep me and everybody else that has kindly been reposting from doing so.



Flushing and Cleaning the 6.0

This is not the Ford flush procedure nor is it the only way to flush the 6.0. It is the procedure I use and I post it as a guide for anyone who isnít sure how to proceed in flushing the 6.0. The bottom line is any procedure that gets all the old stuff out and the new stuff in will work.

Restore is for cleaning out any silicate goo. VC-9 is for cleaning out iron and scale. Restore Plus is the same as VC-9 and cheaper.

To flush drain the coolant by removing the lower radiator hose from the radiator, and removing the drain plug from the driver side of the block. There is a drain plug on the passenger side also but you have to remove the starter to get to it. I don't bother with that one. You can skip the block drains if you want except for the final drain before adding fresh coolant. You will just have to flush a few more times to get the block clear.

I also highly recommend you pull the thermostat out on your first drain and put the housing back without the thermostat. It only takes about 10 minutes and will save you 2.5 hrs or so in doing this whole procedure.

Ok now put the lower hose back on and the drain plug back in the block if you removed it. This is the procedure you will use each time to drain the system, except you will not touch the thermostat again until you're finished the whole procedure. Make sure that you set your heater to high while doing this to flush out the heater core as well.

Fill the cooling system with tap water, start the truck and let the water circulate for 5 minutes. (if you did not remove the thermostat you must run the truck until the thermostat opens + 5 minutes to circulate. This takes 15 to 20 minutes each cycle and is why you should just remove the thermostat) Stop the engine. Drain the system and repeat the flush.

Now add at least 1/2 gallon of Restore and fill with water. Drive truck or run on high idle for 60-90 minutes. Drain and flush 3 or 4 times.

Add 2qts VC-9 or 1/2gal of Restore Plus, top with water, and drive the truck or run on high idle for 60-90 minutes. Now drain and flush until flush water comes out clear and clean. When you get clean flush water, flush 3 more times using distilled water if you are draining the block or 5 times if not. This is to replace any tap water in the cooling system with distilled water and very important.

After your final distilled water drain it is time to put the thermostat back in. I recommend you install a new thermostat at this point. They are only $20 or so and it is good maintenance procedure to do so. Fill with 3.5 or 4 gals of ELC concentrated coolant and top off with distilled water. Drive the truck or let run for a while topping off with distilled water. Check the truck over the next few days and top up as required while any air left in the system works its way out.

Keep some 50/50 ELC on hand to use to top off the cooling system from here out and you are good to go.

Hope this helps.

Mitch aka PGreenSVT

RIP Mitch

To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
the Org crew
PGreenSVT is offline  
The Following 5 Users Say Thank You to PGreenSVT For This Useful Post:
06Greenstroker (05-19-2014), firett (01-16-2014), flattop 6.0 (01-17-2015), IRingTwyce (03-20-2014), Virgil B. (03-13-2015)
Sponsored Links
Advertisement
 
post #2 of 2 Old 07-28-2011, 07:53 AM
Emergency Services

 
TxFireman1972's Avatar
 
Join Date: Mar 2008
Location: Beaumont Texas
Posts: 4,125
Thanks: 0
Thanked 2 Times in 2 Posts
Mentioned: 2 Post(s)
Quoted: 0 Post(s)
Feedback Score: 6 reviews
VERY good info. Might be good to add a "parts list" at the beginning, and maybe even include pictures (I'm big on pictures lol), so people know exactly what they need to buy when they are preparing for this. Thanks for the write up!!
bgraiders323 and Bowser blue like this.

2005 F350 Crew Cab 4x4

PMF Rear Leaf Spring Conversion w/2011 Leaf Springs
20" Harley Wheels 305/55/20 Nitto Terra Grapplers
ARP Studs & EGR Delete from PowerStrokeMagic w/GearHead Tunes
Amp Research Steps, MBRP


To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.


"Two in the heart, and one in the head, I don't like repeat offenders, I like dead offenders!" -- Ted Nugent
TxFireman1972 is offline  
Sponsored Links
Advertisement
 
Reply

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the Ford Powerstroke Diesel Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in










Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode



Posting Rules  
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome