Fabtech dual steering stabilizer install question. - Ford Powerstroke Diesel Forum
Suspension & Steering Discuss OEM & aftermarket suspension, lifts, air ride suspension, shocks, steering components, etc.

Powerstroke.org is the premier Diesel Truck Forum on the internet. Registered Users do not see the above ads.
Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 09-14-2012, 04:02 AM
Powerstroke.org Rookie
 

Join Date: Sep 2012
Posts: 22
Thanks: 0
Thanked 0 Times in 0 Posts
Feedback Score: 0 reviews
Fabtech dual steering stabilizer install question.

Finally got through installing my fabtech 6" radius arm lift and am now installing the steering stabilizer. I have got it all set in place but it looks like im going to have an interference issue between the passenger side shock bracket and the steering arm adjuster clamps. I was going to rotate the clamp out of the way but the clamp on the right is a locator and prevents this. I could take it off and rotate it but am concerned the clamp might hit something else.
Reply With Quote Quick reply to this message
Sponsored Links
Advertisement
 
  #2  
Old 09-14-2012, 04:06 AM
Powerstroke.org Rookie
 

Join Date: Sep 2012
Posts: 22
Thanks: 0
Thanked 0 Times in 0 Posts
Feedback Score: 0 reviews
Picture...
Attached Thumbnails
Fabtech dual steering stabilizer install question.-20120913_205317.jpg  
Reply With Quote Quick reply to this message
  #3  
Old 09-14-2012, 05:22 PM
Premium Member
 

Join Date: Jan 2012
Location: Fallon, Nv
Posts: 2,402
Thanks: 52
Thanked 9 Times in 8 Posts
Feedback Score: 0 reviews
The Fab Tech site shows the adjusting hardware point strait up on their dual stabilizer shot. Not sure wha tthat would do for your steering wheel, but it looks like a good way to avoid problems.

http://www.fabtechmotorsports.com/pr...9&display=FORD 4WD

Last edited by Karls03; 09-14-2012 at 05:30 PM.
Reply With Quote Quick reply to this message
  #4  
Old 09-15-2012, 05:40 AM
Powerstroke.org Rookie
 

Join Date: Sep 2012
Posts: 22
Thanks: 0
Thanked 0 Times in 0 Posts
Feedback Score: 0 reviews
Thanks...i also talked with fabtech and they told me to rotate their bracket forward. This gave me the clearance i needed. It just didnt seem right as the area where the bracket clamps is square and now its not sitting flat but thats ok.
Reply With Quote Quick reply to this message
Sponsored Links
Advertisement
 
Reply

Quick Reply
Message:
Options

Register Now

In order to be able to post messages on the Ford Powerstroke Diesel Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Thread Tools
Display Modes

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -8. The time now is 03:38 AM.


Powered by vBulletin® Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO 3.6.1
Garage Plus, Vendor Tools vBulletin Plugins by Drive Thru Online, Inc.

vB.Sponsors