Ford Powerstroke Diesel Forum - View Profile: JUGERNAUT
Powerstroke.org is the premier Diesel Truck Forum on the internet. Registered Users do not see the above ads.


JUGERNAUT JUGERNAUT is online now

Powerstroke Techie

Visitor Messages

Showing Visitor Messages 1 to 10 of 10
  1. jcpsuperduty
    05-17-2014 05:29 PM - permalink
    jcpsuperduty
    Good evening. you had a post on here about the 6.7 pump. Did you complete the install? If so can you give me a parts list as I have a pump laying around and would like to install it on my truck.
  2. ebaby
    02-05-2014 11:53 AM - permalink
    ebaby
    I have a 03 6.0 my truck started running bad then it would not start after it was warm and I had a guy hook up a scanner to and its only reading 1700 psi is this my high pressure oil pump
  3. JUGERNAUT
  4. CFoster
    10-07-2013 03:50 PM - permalink
    CFoster
    Hey man , I'm in the Hershey- Harrisburg area this week for the antique show.... are you near here?
  5. beckhamslawn
    09-21-2013 02:29 PM - permalink
    beckhamslawn
    Im not sure if you got my reply to your comment on my thread. I am a new member(few hours)
  6. jandjkemp
    09-12-2013 07:17 PM - permalink
    jandjkemp
    Hi. I'm looking for help with 06 f350 I just bought. I got it from a used lot who purchased it at auction. Being unable to speak with the previous owner, I don't know what warranty work was done to this 6.0. Tried to speak with my local dealership about it and they refused to give me any info.
  7. ldhost1
    07-06-2013 09:20 AM - permalink
    ldhost1
    I need some help. After I did all the work, I'm getting high ICP voltage. It is 4.8 all the time. Doesn't move at all. Any ideas? Is it ok to drive?
  8. PGreenSVT
    01-12-2013 06:27 PM - permalink
    PGreenSVT
    stuck it
  9. Tuscany
    12-14-2012 02:04 AM - permalink
    Tuscany
    LOL we were but something happened?? I lost ALL of my friends so I had to just go back through and re-add EVERYONE lol.
  10. jonesy_11950
    09-20-2012 01:36 PM - permalink
    jonesy_11950
    Can you tell me what the valve to piston clearance is? I have an 04 6.0l and did the clay test to determine PTV clearance. I can not find info on it. My results of this was .0062 and .0073. Not sure if valves would hit piston with that result. Thanks Michael

About Me

  • About JUGERNAUT
    State/Province
    Pennsylvania
    Gender
    Male
    How did you find Powerstroke.org
    web site
    Biography
    been with ford 26 years and just got my 10 year senior master in all 3 sections.
    Interests
    3 kids,r/c aircraft,karate 6 months from black belt and mauh thia
    Exact Location
    UPPER SALFORD PA
    Occupation
    SENIOR MASTER FORD TECH
    Ride
    03 f250 super duty
    Engine
    POWERMAX
    Cab Configuration
    Extended Cab Long Box
    Drivetrain
    Single Rear Wheel 4X4
    Tranny type
    Torqshift
    Tires
    All Terrain
    Modifications
    arp,egr delete,airbox,exhaust,52v ficm,65psi reg,
    Primary Vehicle Use
    back and forth to work
    Horsepower
    0.0
    1/8 Mile ET
    0.000
    1/8 Mile MPH
    0.00
    1/4 Mile ET
    0.000
    1/4 Mile MPH
    0.00
  • Signature

    2001 to 2013 SENIOR MASTER TECHNICIAN
    BEEN WITH FORD 26 YEARS:
    PROUD NAVY VET= ANTI SUBMARINE WARFARE
    A/C ASW A/W WINGS


    http://www.gofundme.com/5cr55s

Statistics

Total Posts
Visitor Messages
Total Thanks
General Information

Friends

Showing Friends 1 to 10 of 72

Feedback Score

iTrader Profile Recent Ratings
Feedback Score:
Positive Feedback:
13
100.0%
Members who left positive:
Members who left negative:
13
0
Total positive feedback: 13
View Complete Feedbacks for JUGERNAUT
  Past
Month
Past
6 Months
Past
12 Months
 Positive 0 0 3
 Neutral 0 0 0
 Negative 0 0 0

All times are GMT -8. The time now is 04:57 AM.


Powered by vBulletin® Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO 3.6.1
Garage Plus, Vendor Tools vBulletin Plugins by Drive Thru Online, Inc.

vB.Sponsors