Ford Powerstroke Diesel Forum banner

FLOstroked's Look at me thread.....

9K views 43 replies 8 participants last post by  FLOstroked 
#1 · (Edited by Moderator)
2015 F250 Super Duty Lariat 6.7l 15k miles. Picked her up yesterday and had a few goodies ordered even before I got the keys. New to trucks/diesel but not new to modding...this shall be fun. Hope to learn the ins/out of my engine here and get some creative ideas.

Didn't like the dealership key chain, so I printed my own.
 

Attachments

See less See more
2
#2 ·
#4 ·
Now awaiting delivery of:

Bushwacker pockets
Rear wheel well liners
Lift gate shock
WeatherTech window trim
Hitch insert
S&B Intake (will be replaced with NL Stage2 when ready for tuning and deletes)
BD Throttle Controller w/button

Since so many cup holders, I designed and 3d printed a Samsung Note5 (landscape) holder...will post pic soon...need to make a slight rev to it.
 
#5 · (Edited)
Going to turn this into my history thread.

Recently installed:
3D printed Note5 (cup) holder
Bushwacker Fender Flares
BD Throttle Boost w/push button
Weather Tech Rain Guards
Trailer Hitch Ford Insert

Awaiting install:
Lift Gate shock
Rear Wheel well liners
PlastiDip front/rear emblems

Awaiting arrival of audio goodies:
JL Audio C2-350x 3.5" 25 Watts RMS
JL Audio 13TW5V2 2 ohms 600 Watts RMS
JL Audio 500/1v2 Slash Amp
Focal PS 165 6.5" 160 Watts RMS Component
Audio Control LC2i LOC
SuperCrewSound 13.5" JL Box .8cf
Stinger 4ga 4000 Seriel Amp Kit
50 Amp Mini ANL Fuse
Monster THX-Certified RCA Cables
Dynamat 10435 Xtreme w/wood roller
6x8 to 6.5" Speaker Adapter
Touch Up Paint
Touch Up Primer

Next:
Front Grill
30" Light Bar
Add Interior lighting near feet and crew cab area...too dark at night
 
#12 · (Edited)
My 3D printed Note5 Cell phone holder. Just need to print out Red Scorpions. Not 100% perfect fitting...didnt note the rounded down corners until after printing...might fix..but good enough for m for now. With the ottercase around my Note5...has yet to tip over/fall out.
 

Attachments

#16 ·
Ordered:
Flo Pro 5" Aluminum single full exhaust
Flo Pro 5" to 6" powder coated clamp on tip
RetroSoultions High/Low LED
RetroSolutions Fog Light LED
RetroSolutions Interior LEDs
RetroSolutions 40" Curved LightBar
KD Fabworks 40" Curved LightBar Mounts
KD Fabworks Tow Hook Eliminate Kit

Once the money tree regens:
NL Full EGR delete kit
NL Stage 2 Intake
SCT Livewire w/GH tunes
 
#22 ·
Since I can no longer in good spirit wear my BMW M5 hats...this happened.
Another set of LED strips for front/rear enabled when arming/disarming/ opening doors
F R letters for my Ford Raptor grill
Bumper support removal tools
5" to 6" Flo Pro Powder Coated Tip
5" full Flo Pro Exhaust





 
#26 ·
What did you wire the to so they only come on when you open the doors ? I'm talking about running board lights
 
#29 ·
1 Sundown SCV3000D
1 Sundown SAE100.4
2 Sundown X8's D2 in ported box to 33Hz @ .5ohms
Extra XS Battery w/2 inline 250amp fuses
0 Gauge
Custom Center console firing down (thread to follow once this project gets started)
 
#31 ·
Swapped out old headlights for new Spyder. Had to design/3d print a dust boot adapter as well as LED secure ring for lo-beam.

In the process of designing the fender grill for a local Excursion owner. Might just make a "Recon Style" LED grill...we shall see.
 

Attachments

This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Top