Trans will not go! - Ford Powerstroke Diesel Forum

 
LinkBack Thread Tools Display Modes
post #1 of 9 Old 09-21-2009, 02:26 PM Thread Starter
Powerstroke.org Rookie
 
Join Date: Jun 2009
Posts: 7
Thanks: 0
Thanked 0 Times in 0 Posts
Mentioned: 0 Post(s)
Quoted: 0 Post(s)
Feedback Score: 0 reviews
Trans will not go!

Hey everyone,

I have a 2000 f250 7.3l 4x4 automatic 4r100 with a few upgrades. I have a TS chip stage 2 garrett turbo 75 flow injectors and 4 inch exhaust. I just had the trans rebuilt and I just installed it in my truck last night. I put it into gear and it started driving but would not shift past second gear. Anyways I drive it around for about 5 mins and the it started shifting fine. But when i pulled back in the driveway, it wouldnt go into reverse. It acted like it was slipping real bad. Now it wont go into any gear except for when I shut the truck off and restart it and immediately put it into gear and then it will only stay in gear for about 30 seconds and then it starts slipping and then quits. I replaced the torque converter before I put the trans in and the shift solenoid and valve body was replaced as well.

Any input would be greatly appreciated.

**Codes im getting are:
P0603 - Internal Control Module
P0478 - Exhaust Pressure Control Valve High
P0470 - Exhaust Pressure Sensor Circuit Fault
P0708 - Trans Range Sensor Circuit High Input
P0741 - Torque Converter Clutch System Stuck Off

Last edited by yllwevo; 09-21-2009 at 02:52 PM.
yllwevo is offline  
post #2 of 9 Old 09-21-2009, 03:35 PM
Compression Ignition Addict
 
HOUTX01X's Avatar
 
Join Date: Jul 2009
Location: Houston, Texas
Posts: 699
Thanks: 10
Thanked 2 Times in 2 Posts
Mentioned: 0 Post(s)
Quoted: 4 Post(s)
Feedback Score: 0 reviews
I would take it back to whom ever rebuilt it. did come with a warranty?

'11 F250 KR
XRT Pro, H&S SX-E turbo kit, NoLimit intake/intercooler
OUO bars/blocks
Ř-EGR,CCV,1993pf
Leveled w/ 35 atII
HOUTX01X is offline  
post #3 of 9 Old 09-21-2009, 03:39 PM
Compression Ignition Addict
 
7004's Avatar
 
Join Date: Jul 2008
Location: Bessemer City
Posts: 333
Thanks: 0
Thanked 0 Times in 0 Posts
Mentioned: 0 Post(s)
Quoted: 0 Post(s)
Feedback Score: 0 reviews
not good . who rebuilt it ? did you get a warranty?



Early '99 F-350 Ext. Cab LB
TS 6pos. Chip
Tranne is all better
K&N Intake
Zoodad mod
4" Downpipe
MBRP 5" Exhaust w/6" SS Tip
Boost Fooler
Quadzilla Recon
(Sold)'96 F-250 Ext. Cab LB
CENTER][URL
7004 is offline  
post #4 of 9 Old 09-21-2009, 03:41 PM
wriott
Guest
 
Posts: n/a
Mentioned: Post(s)
Quoted: Post(s)
is the fluid full?? i know when i had mine rebuilt i had have almost all fluid in before it would move... check the fluid and add it if needed
post #5 of 9 Old 09-21-2009, 04:18 PM Thread Starter
Powerstroke.org Rookie
 
Join Date: Jun 2009
Posts: 7
Thanks: 0
Thanked 0 Times in 0 Posts
Mentioned: 0 Post(s)
Quoted: 0 Post(s)
Feedback Score: 0 reviews
Yeah the fluid is fine. The guy who rebuilt it thinks it electrical. Possibly a sensor or in the wire harness. He's not sure and he is definately dragging his feet about returning my calls.
yllwevo is offline  
post #6 of 9 Old 09-22-2009, 02:37 PM Thread Starter
Powerstroke.org Rookie
 
Join Date: Jun 2009
Posts: 7
Thanks: 0
Thanked 0 Times in 0 Posts
Mentioned: 0 Post(s)
Quoted: 0 Post(s)
Feedback Score: 0 reviews
Anyone have any further thoughts or ideas? All input is greatly appreciated. The guy is coming out tonight with a scanner again so I'll let you know if I have anymore updates. thanks
yllwevo is offline  
post #7 of 9 Old 09-27-2009, 06:05 PM
Powerstroke.org Rookie
 
Join Date: Aug 2009
Posts: 5
Thanks: 0
Thanked 0 Times in 0 Posts
Mentioned: 0 Post(s)
Quoted: 0 Post(s)
Feedback Score: 0 reviews
It almost sounds like a valve body problem.I've been down the say road with a jackass guy that never made good with me. I gave up and bought a suncoast trans that I just broke a few hours ago, I'm hopein it is just a input shaft
bmanzi is offline  
post #8 of 9 Old 10-16-2009, 11:10 PM
Compression Ignition Addict
 
blue72's Avatar
 
Join Date: Aug 2009
Location: Kingsport, TN
Posts: 377
Thanks: 5
Thanked 0 Times in 0 Posts
Mentioned: 0 Post(s)
Quoted: 0 Post(s)
Feedback Score: 5 reviews
Any update on this?

2000 F350 XLT SCLB 4x4
PHP 6 Pos. Chip
DIY 6637 Induction
Walker Muffler
Stewart Warner Gauges
blue72 is offline  
post #9 of 9 Old 12-10-2009, 03:27 PM Thread Starter
Powerstroke.org Rookie
 
Join Date: Jun 2009
Posts: 7
Thanks: 0
Thanked 0 Times in 0 Posts
Mentioned: 0 Post(s)
Quoted: 0 Post(s)
Feedback Score: 0 reviews
Well looks like the problem was low gear was screwed up and it burnt the brand new hd clutches up so he had to rebuild it again. All seems to be running good now so we will see if anything else happens
yllwevo is offline  
Reply

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the Ford Powerstroke Diesel Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in









Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode



Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome