RPM surge - Ford Powerstroke Diesel Forum
 
LinkBack Thread Tools Display Modes
post #1 of 8 Old 06-02-2008, 05:37 PM Thread Starter
Compression Ignition Addict
 
Gruss's Avatar
 
Join Date: Mar 2008
Location: New Brighton PA
Posts: 1,107
Thanks: 0
Thanked 1 Time in 1 Post
Mentioned: 0 Post(s)
Quoted: 0 Post(s)
Feedback Score: 0 reviews
RPM surge

Ok new problem, I get a rpm surge while driving at just off idle, Not all the time every now and then. Seams to be more noticeable the first mile after start up then gets better. No CEL no tranny slipping(truck accelerates with rpm surge) fuel filter has only 1000 miles on it, but I'm running WVO 50/50 mix. I'm had filter clog before and this isn't acting like that. Any ideas?

Quote:
"If you want smoke, work for it. These guys did" JJFLASH


Stormtrooper:: 1997 F-350 CC SRW PSD XLT 4X4: Baby Swamps, Wildman 4 pos chip, 120V IDM, SD Intercooler,BTS E4OD, RSK, CCV mod, shimmed FPR, DIY 6637 air filter, triple pillar pod with Isspro gauges, 4" MBRP exhaust, SD dual tensioner,
Gruss is offline  
Sponsored Links
Advertisement
 
post #2 of 8 Old 06-02-2008, 05:44 PM
Compression Ignition Addict
 
Join Date: Jan 2008
Location: cedaredge colorado
Posts: 659
Thanks: 0
Thanked 0 Times in 0 Posts
Mentioned: 0 Post(s)
Quoted: 0 Post(s)
Feedback Score: 0 reviews
what rpm does it do it at and does it do it when it is in park and you slowly rev it
badazzstroker is offline  
post #3 of 8 Old 06-02-2008, 05:59 PM Thread Starter
Compression Ignition Addict
 
Gruss's Avatar
 
Join Date: Mar 2008
Location: New Brighton PA
Posts: 1,107
Thanks: 0
Thanked 1 Time in 1 Post
Mentioned: 0 Post(s)
Quoted: 0 Post(s)
Feedback Score: 0 reviews
It happens just above idle, I's say around 900-1000 rpms. Never noticed it in park. It acts just like you hit a bump on a rough road and blip the pedal.

Quote:
"If you want smoke, work for it. These guys did" JJFLASH


Stormtrooper:: 1997 F-350 CC SRW PSD XLT 4X4: Baby Swamps, Wildman 4 pos chip, 120V IDM, SD Intercooler,BTS E4OD, RSK, CCV mod, shimmed FPR, DIY 6637 air filter, triple pillar pod with Isspro gauges, 4" MBRP exhaust, SD dual tensioner,
Gruss is offline  
post #4 of 8 Old 06-02-2008, 06:37 PM
Compression Ignition Addict
 
Join Date: Jan 2008
Location: cedaredge colorado
Posts: 659
Thanks: 0
Thanked 0 Times in 0 Posts
Mentioned: 0 Post(s)
Quoted: 0 Post(s)
Feedback Score: 0 reviews
i have seen a lot of powerstrokes do just what you say when the orings on the ipr valve need replaced. it will almost never throw a code though.i would get the codes pulled and if there are none you might just swap out those orings and see what happens.it has worked many times on other 7.3 and cat motors as well.easy to do and cheap.
badazzstroker is offline  
post #5 of 8 Old 06-02-2008, 07:01 PM Thread Starter
Compression Ignition Addict
 
Gruss's Avatar
 
Join Date: Mar 2008
Location: New Brighton PA
Posts: 1,107
Thanks: 0
Thanked 1 Time in 1 Post
Mentioned: 0 Post(s)
Quoted: 0 Post(s)
Feedback Score: 0 reviews
Is this what I need? 7.3L Powerstroke IPR Valve Reseal Kit

Quote:
"If you want smoke, work for it. These guys did" JJFLASH


Stormtrooper:: 1997 F-350 CC SRW PSD XLT 4X4: Baby Swamps, Wildman 4 pos chip, 120V IDM, SD Intercooler,BTS E4OD, RSK, CCV mod, shimmed FPR, DIY 6637 air filter, triple pillar pod with Isspro gauges, 4" MBRP exhaust, SD dual tensioner,
Gruss is offline  
post #6 of 8 Old 06-02-2008, 07:04 PM
Compression Ignition Addict
 
Join Date: Jan 2008
Location: cedaredge colorado
Posts: 659
Thanks: 0
Thanked 0 Times in 0 Posts
Mentioned: 0 Post(s)
Quoted: 0 Post(s)
Feedback Score: 0 reviews
yea that is the one.
badazzstroker is offline  
post #7 of 8 Old 06-02-2008, 07:05 PM
Compression Ignition Addict
 
Join Date: Jan 2008
Location: cedaredge colorado
Posts: 659
Thanks: 0
Thanked 0 Times in 0 Posts
Mentioned: 0 Post(s)
Quoted: 0 Post(s)
Feedback Score: 0 reviews
you can also get it at ford for about 40.00 or 50.00 bucks
badazzstroker is offline  
post #8 of 8 Old 06-02-2008, 07:17 PM Thread Starter
Compression Ignition Addict
 
Gruss's Avatar
 
Join Date: Mar 2008
Location: New Brighton PA
Posts: 1,107
Thanks: 0
Thanked 1 Time in 1 Post
Mentioned: 0 Post(s)
Quoted: 0 Post(s)
Feedback Score: 0 reviews
Thanks I'll give that a shot, I just had an high pressure oil rail o-ring fail so it looks like all the rubber is getting old.

Quote:
"If you want smoke, work for it. These guys did" JJFLASH


Stormtrooper:: 1997 F-350 CC SRW PSD XLT 4X4: Baby Swamps, Wildman 4 pos chip, 120V IDM, SD Intercooler,BTS E4OD, RSK, CCV mod, shimmed FPR, DIY 6637 air filter, triple pillar pod with Isspro gauges, 4" MBRP exhaust, SD dual tensioner,
Gruss is offline  
Sponsored Links
Advertisement
 
Reply

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the Ford Powerstroke Diesel Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in









Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode



Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome