Where's my ECM - Ford Powerstroke Diesel Forum
User Tag List

LinkBack Thread Tools Display Modes
post #1 of 4 Old 06-15-2008, 09:09 PM Thread Starter
Compression Ignition Addict
Join Date: Dec 2007
Posts: 226
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Thanks: 0
Thanked 0 Times in 0 Posts
Feedback Score: 0 reviews
Where's my ECM

Where's my ecm located in my truck?

1995 F250 7.3 turbo
3 inch dp into 4 inch exhaust
tymar intake, Isspro boost, pyro, tranny temp gauges
tow and go shift kit, DIY electric fuel pump system with fuel pressure gauge,bronco tank mod
kcm ss hpx line, stancor gpr, 203 thermostat, 03 starter
TWchip 6 postion daily,econo,tow,street,xtreme,highidle
Banks intercooler and pipe kit,Idm Mod,CCV Mod
Plant drive wvo kit(hotfox,vegmax filters,26fphe, vegthermmega and gauges for cooliant and wvo temp)
Dana 60 front axle swap
7.3TurboDiesel is offline  
Sponsored Links
post #2 of 4 Old 06-15-2008, 09:33 PM
Compression Ignition Addict
Join Date: May 2008
Location: Bridgeview, IL.
Posts: 164
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Thanks: 0
Thanked 0 Times in 0 Posts
Feedback Score: 0 reviews
the computer is located on the left side of the parking brake pedal, you have to remove the parking brake pedal to take the computer out, i never got it out though, had to put chip in with it still half way in the truck, unplugged of course.
95superstroke is offline  
post #3 of 4 Old 06-15-2008, 09:45 PM
Premium Member
SMKSTAX's Avatar
Join Date: May 2007
Location: Effort/Nanticoke,Pa.
Posts: 5,441
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Thanks: 0
Thanked 0 Times in 0 Posts
Feedback Score: 0 reviews
Chock the wheels of your truck. Use a 3/8 drive ratchet with a 1/2" deep socket to take out the 3 nuts that hold on your parking brake assembly. Undo the clip attached to the wire from the top of the assembly. Slide off the entire assembly and set it down on the floor. Behind that you will see your computer and the stock chip will be sticking out of the back. I see you ordered a chip from Tony, you will not be disappointed!



SMKSTAX is offline  
post #4 of 4 Old 06-15-2008, 10:21 PM
Electrical Ogre
alberta 7.3's Avatar
Join Date: Aug 2007
Location: Calgary, Alberta
Posts: 11,984
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 9 Post(s)
Thanks: 30
Thanked 71 Times in 68 Posts
Feedback Score: 1 reviews
To actually pull out the computer to properly clean the service port connection to add the chip (and remove port cover,) from the engine compartment, undo bolt in PCM connector (10mm) and remove weatherstrip flange (2 10mm nuts.) Undo bolts from fender wheel lip to plastic splash shield. Press splash shield toward tire and slide computer out off recess in firewall. For chip install, noting static precautions, remove plastic service port cover, and remove 4 4mm? head bolts on computer case. Lift off tin cover, then separate computer box sections. CAREFULLY "drag" away silicone sealer from both sides of service port card edge connector using razor or x-acto blade. Clear away remaining residue with alcohol and q-tips. Reassemble case and plug in chip. For chips with switches (multi position,) removing the parking brake pedal will allow ease of fishing the switch harness to the desired dash location.


1996 F250 SC/SB 4X4 XLT
1997 F250 RC/SB 2WD project
2008 F350 CC/LB 4X4 DRW Lariat, 3" cow catcher mod
2008 Ranger SC FX4
Originally Posted by weareweird69 View Post
If your posting pictures bill, everyone dim their screens, that CAT YELLOW is bright
Originally Posted by Fordman247365 View Post
Is there anything you DONT take apart and **** with?
Originally Posted by JJFLASH View Post
I still say that those Dodge mirrors have as much business on a OBS Ford as yoga pants have on a fat chick...my .02
alberta 7.3 is online now  
Sponsored Links

Quick Reply

Register Now

In order to be able to post messages on the Ford Powerstroke Diesel Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Please enter a password for your user account. Note that passwords are case-sensitive.


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:


Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.

Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

For the best viewing experience please update your browser to Google Chrome