R Injector Cups Still OK?? - Ford Powerstroke Diesel Forum

 
LinkBack Thread Tools Display Modes
post #1 of 2 Old 09-12-2012, 06:42 PM Thread Starter
Compression Ignition Addict
 
FreightShaker244's Avatar
 
Join Date: Sep 2012
Posts: 154
Thanks: 0
Thanked 1 Time in 1 Post
Mentioned: 0 Post(s)
Quoted: 0 Post(s)
Feedback Score: 0 reviews
R Injector Cups Still OK??

I have a 1995 powerstroke with AO injectors. I replaced the injector o-rings in january due to oil back feeding into my fuel tank and drained the oil pan. truck ran fine for for 4 months than on start up it would smoke white-ish smoke at start up until engine warmed up, and had no power.

i thought it might be a injector issue so i got a free 99 7.3 motor with newer AB injectors in it so im swapping them over (custom tune from DP going to be ordered once installed).

I started pulling the injector harness 2 cylinders from pass side when first start up and pin pointed to 2 injectors that were acting up. pulled the injectors and found the hold down bolts wernt TIGHT but snug they were torqued down when o-rings were done. when pulled the ends of injectors that sit in cup were covered in carbon. injector cups dont look cracked or anything.

My QUESTION: would my injector cups still be okk or should they be changed out.

1995 F-250 7.3 Powerstroke 5 Speed, 6'' Lift. DIY Intake/Napa filter, 4" exhaust.
FreightShaker244 is offline  
post #2 of 2 Old 09-13-2012, 09:53 AM Thread Starter
Compression Ignition Addict
 
FreightShaker244's Avatar
 
Join Date: Sep 2012
Posts: 154
Thanks: 0
Thanked 1 Time in 1 Post
Mentioned: 0 Post(s)
Quoted: 0 Post(s)
Feedback Score: 0 reviews
Here's pictures of the injectors when pulled.. All o-rings all still in new condition. One copper washer is "lose" on injector tip.

Any ideas if cups might still be ok??


Sent from my iPhone using Autoguide
Attached Thumbnails
Click image for larger version

Name:	ImageUploadedByAutoguide1347558690.696945.jpg
Views:	85
Size:	8.0 KB
ID:	43032   Click image for larger version

Name:	ImageUploadedByAutoguide1347558705.457171.jpg
Views:	66
Size:	7.4 KB
ID:	43033  

1995 F-250 7.3 Powerstroke 5 Speed, 6'' Lift. DIY Intake/Napa filter, 4" exhaust.
FreightShaker244 is offline  
Reply

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the Ford Powerstroke Diesel Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in









Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode



Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome