Need Spicer Part# for front axle joints and ball joint recommendation for 97 250 4x4 - Ford Powerstroke Diesel Forum
 
LinkBack Thread Tools Display Modes
post #1 of 4 Old 09-26-2011, 06:54 PM Thread Starter
Powerstroke.org Rookie
 
95f-350's Avatar
 
Join Date: Jan 2010
Location: grayson,ky
Posts: 16
Thanks: 0
Thanked 0 Times in 0 Posts
Mentioned: 0 Post(s)
Quoted: 0 Post(s)
Feedback Score: 0 reviews
Need Spicer Part# for front axle joints and ball joint recommendation for 97 250 4x4

Going to replace the front end in the 97 250 xcab 4x4.Just wanted some recommendation on ball joints and part #s, and anything else you think I might take a look at while I got it apart,it also still has the Auto 4x4 hubs.
95f-350 is offline  
Sponsored Links
Advertisement
 
post #2 of 4 Old 09-26-2011, 07:04 PM
Delivers Pizzas For Fun!
 
ol_Blue97's Avatar
 
Join Date: Apr 2010
Location: cecil county MD
Posts: 6,024
Thanks: 1
Thanked 18 Times in 16 Posts
Mentioned: 3 Post(s)
Quoted: 0 Post(s)
Feedback Score: 0 reviews
your gonna want the hub puller that attaches to a slidehammer.. dont mess around, get it b4 you start. makesure you check the inner spindle berings and seals. this is the one that axle shaft rides on while going thru the spindle. it a little needle bearing and they have a tendancy to get caked up with junk over time due to the rear seals going bad

dont get junk ball joints... moog, spicer, only two i know off hand.

the bottom nut on the balljoint usually is a mother ****** t get off. it took me 3 broken sockets, a broken breaker bar till i got a 3/4 drive impact socket and bar and a 5 ft cheeter bar!!!! no lie and it took everything i had to get it top break. but i only had propane gas to heat with,

when you reassemble make sure you tighten the bottom ball joint first and then the top ball joint. if you do the top first. the bottom will never seat correctly.

good luck... they can be a PITA sometimes

FRANK THE TANK
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
DIY INTAKE - HYDRA CHIP - MARTY'S E-FUEL - 250/200s
05 AXLE SWAP 3.73 - 2.5" PURE PERF. LIFT COILS - FOX SHOCKS
BTS TRANS - TYMAR DOWN PIPE - 4" EXHAUST
Waiting To Be Installed... gtx4294r, studs, springs, HPOP?

To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
Quote:
Originally Posted by STROKED_NY_023 View Post
You are so smart Frank, I dont care what Terry says.
ol_Blue97 is offline  
post #3 of 4 Old 09-27-2011, 02:42 AM Thread Starter
Powerstroke.org Rookie
 
95f-350's Avatar
 
Join Date: Jan 2010
Location: grayson,ky
Posts: 16
Thanks: 0
Thanked 0 Times in 0 Posts
Mentioned: 0 Post(s)
Quoted: 0 Post(s)
Feedback Score: 0 reviews
This hub puller your talking about is it something I can rent at the parts stores.The inner bearing and seal,I noticed a seal hanging loose on one of the axles,probably the one your talking about.Still need a spicer # for the front axle U-joints and it has auto 4x4,thanks!
95f-350 is offline  
post #4 of 4 Old 09-27-2011, 07:10 PM
Delivers Pizzas For Fun!
 
ol_Blue97's Avatar
 
Join Date: Apr 2010
Location: cecil county MD
Posts: 6,024
Thanks: 1
Thanked 18 Times in 16 Posts
Mentioned: 3 Post(s)
Quoted: 0 Post(s)
Feedback Score: 0 reviews
cant help you on the number and no i couldnt find one to rent. bought it at napa. its an OTC tool i belive

FRANK THE TANK
To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
DIY INTAKE - HYDRA CHIP - MARTY'S E-FUEL - 250/200s
05 AXLE SWAP 3.73 - 2.5" PURE PERF. LIFT COILS - FOX SHOCKS
BTS TRANS - TYMAR DOWN PIPE - 4" EXHAUST
Waiting To Be Installed... gtx4294r, studs, springs, HPOP?

To view links or images in signatures your post count must be 10 or greater. You currently have 0 posts.
Quote:
Originally Posted by STROKED_NY_023 View Post
You are so smart Frank, I dont care what Terry says.
ol_Blue97 is offline  
Sponsored Links
Advertisement
 
Reply

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the Ford Powerstroke Diesel Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in









Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page
Display Modes
Linear Mode Linear Mode



Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome