Installing uplifter switches in a 03. - Ford Powerstroke Diesel Forum
6.0L Electronics Discussion TV's, Radios, everything electric and NON-Performance.

Powerstroke.org is the premier Diesel Truck Forum on the internet. Registered Users do not see the above ads.
Reply
 
LinkBack Thread Tools Display Modes
  #1  
Old 10-05-2012, 04:13 PM
Powerstroke Tech

 

Join Date: May 2010
Posts: 169
Thanks: 0
Thanked 0 Times in 0 Posts
Feedback Score: 0 reviews
Installing uplifter switches in a 03.

Has anyone installed the uplifter switched from an 05-07 in a 03-04? if so how was it done, was it just plug the kit in and connect some wires?
Reply With Quote Quick reply to this message
Sponsored Links
Advertisement
 
  #2  
Old 10-05-2012, 10:38 PM
Compression Ignition Addict
 

Join Date: Mar 2008
Location: Santa Rosa, CA
Posts: 1,347
Thanks: 0
Thanked 4 Times in 4 Posts
Feedback Score: 0 reviews
In an 05 or newer the switches have a plug that just plugs into the fusebox, but 99-04 Superdutys don't have the plug in the fusebox so you will just have to wire them in yourself.

It shouldn't be to hard with a wiring diagram, so here is one: https://www.fleet.ford.com/TRUCKBBAS/non-html/Q117.pdf

Reply With Quote Quick reply to this message
  #3  
Old 10-06-2012, 09:33 AM
Powerstroke Tech

 

Join Date: May 2010
Posts: 169
Thanks: 0
Thanked 0 Times in 0 Posts
Feedback Score: 0 reviews
ok thank you, ive seen numerous posts about this topic but none specifying the sjb (smart junction box ) connector.
Reply With Quote Quick reply to this message
  #4  
Old 02-20-2013, 03:42 PM
Powerstroke Tech

 

Join Date: May 2010
Posts: 169
Thanks: 0
Thanked 0 Times in 0 Posts
Feedback Score: 0 reviews
got everything in and working. had to change the lower dash pannel, cup holder, add the pull down compartment, and the little panel with the hook on it .I also had to do a little trim here and there for everything to fit right. As far as the wiring goes i bought a 4 fuse fuse block and ran a 10 gauge amp wire off the battery to the fuse block to run power to each of the four switches. Tied the switch relay box in with the ignition switch so the switches only have power with the key on. Over all was an somewhat easy job, hardest part was getting the panel to fit right even that was fairly easy.
http://www.powerstroke.org/forum/mem...-switches.html
Reply With Quote Quick reply to this message
Sponsored Links
Advertisement
 
Reply

Tags
switches, uplifter

Quick Reply
Message:
Options

Register Now

In order to be able to post messages on the Ford Powerstroke Diesel Forum forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.
User Name:
If you do not want to register, fill this field only and the name will be used as user name for your post.
Password
Please enter a password for your user account. Note that passwords are case-sensitive.
Password:
Confirm Password:
Email Address
Please enter a valid email address for yourself.
Email Address:

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Thread Tools
Display Modes

Posting Rules
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -8. The time now is 06:28 AM.


Powered by vBulletin® Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO 3.6.1
Garage Plus, Vendor Tools vBulletin Plugins by Drive Thru Online, Inc.

vB.Sponsors